hal

The Question Booklets are broadly classified into five Disciplines as indicated below:



1) Aeronautical



2) Mechanical and Production



3) Metallurgy



4) Electrical and Electronics



5) Computer Science

Each Question Booklet will have 160 Objective Type Questions, as indicated below:

General Awareness

General Engineering

Questions specific to the

Total

(15 Questions)

(25 Questions)

respective Disciplines

(160 Questions)

indicated above (120

Questions)



15 Marks 25 Marks 120 Marks 160 Marks

Notes

1. The Question Booklet for Mechanical and Production Disciplines will be the same and

candidates will have to answer questions for both Mechanical and Production Branches.



2. The Question Booklet for Electrical and Electronics Disciplines will be the same and candidates

will have to answer questions for both Electrical and Electronics Branches.



キ There are no negative marks for incorrect answers.



キ Please use the blank pages provided at the end of the Question Booklet only for any rough work.



キ If any Candidate is found to be indulging in any kind of malpractice like copying, trying to talk to



other candidates, exchanging information, carrying/passing on chits of paper or any other mode to

communicate with others, his/her candidature shall be cancelled.







キ Mobile Phones, Pagers, Beepers, any kind of Audio Devices, Digital Diaries, Organisers etc.,

shall not be permitted inside the Examination Hall.



キ Candidates will be required to appear for the Written Test at their own expense and will have to

make their own arrangements for boarding and lodging at the place of the Examination.



キ Further consideration of the candidature after the Written Test will be subject to:-



1. Candidates having passed the final Engineering Examination in the specified Branches of Engg.

indicated in the Advertisement, from any recognised Institution/University, with 60% marks in the

Aggregate of all Semesters for General/OBC and 50% Marks in the aggregate of all Semesters for

SC/ST Candidates.



2. Verification of Qualifications, Marks scored, Age, Caste (for SC/ST/OBC only), PWD (Person

with Disability) /Ex-Servicemen etc.

IMPORTANT

Candidates must ensure that they are in possession of the following documents/items, when they

report at the Examination Centre:



キ Admit Card (with Passport Size photograph duly affixed).



キ Proof of Identity having their photograph such as Passport, Voters' ID Card, Driving License, ID

Card issued by the Academic Institution last attended etc., for verification by the Invigilator.

キ HB Pencils, Eraser, Pen and Calculator.


INSTRUCTIONS TO CANDIDATES FOR ANSWERING ON THE OMR ANSWER SHEET



1. Use only HB Pencil to mark the Ovals in the Answer Sheet.



2. Use Ball Point Pen to fill the Boxes (ie for the Question Booklet No., Roll Number, Date of

Birth and Signature.)



3. Indicate the Question Booklet Series and Question Booklet Serial Number in the space

provided on the OMR Answer Sheet without fail.



4. Please mark the relevant Ovals against the columns like Series, Category, Quota and

Main Branch of Engineering as applicable to you.



5. Mark your answer only in the appropriate space against the Number corresponding to the

question you are answering. Darken the response for each question:

A B C D

(ie., if the answer to the Question is option A , then it needs to be darkened )



6. Please ensure that the Ovals are completely darkened.



7. In case of any mistake while marking, please erase the mark completely and fill the correct

Oval again. Do not leave stray marks/half filled Ovals on the Answer Sheet.



8. Rough work must not be done on the Answer Sheet. Use the blank pages given at the end

of the Question Booklet for rough work.

Sample Questions for the Executive Trainees (Technical ) Test

Aeronautical Engineering



2. Air Fuel ratio in a jet engine will be of the order of:

(a) 10:1 (b) 15:1

(c) 20:1 (d) 60:1

3. Fighter bombers use following type of engine:

(a) Turbo-jet (b) Turbo-propeller

(c) Rocket (d) Ram-jet


Mechanical Engineering



6. Least shrinkage allowance is provided in the case of following:

(a) Brass (b) Aluminium

(c) Cast Iron (d) Steel



9. If V is the volume of metal in a casting and A its surface area, the time of solidification will

be proportional to:

(a) V, 1/A (b) V,1/A2

(c ) V2 ,1/A (d) V2, 1/A2

3. Fire tube boilers are limited to a maximum design working pressure of :

(a) 1 kg/cm2 (b) 6 kg/cm2

(C) 17 kg/cm2 (d ) 100 kg/cm2


Metallurgy

1. A dislocation represented by T is called:

(a) Positive edge dislocation

(b) Negative edge dislocation

(c) Positive screw dislocation

(d) Negative screw dislocation



2. The recrystallisation temperature of a cold worked material decreases with:

(a) Increase in the degree of deformation

(b) Increase in the initial grain size

(c) Increase in the temperature of cold working

(d) The presence of impurity

Electrical Engineering



1. In a thyrister full converter feeding a continuous load current, what is the duration each

thyrister conducts in a cycle?

(a) 60 0 (b) 90 0

(c) 120 0 (d) 180 0



2. In a three-phase induction motor, the rotor field runs at the following speed with Respect to the

stator structure:

(a) At synchronous speed in the direction of stator field

(b) At a slip speed in the direction of stator speed

(c) At synchronous speed in a direction opposite to that of stator field

(d) At zero speed


Electronics



1. In the hybrid parameter model of a transistor reverse transfer voltage ratio and forward transfer

current ratio are respectively given by:

(a) h11 and h21 (b) h12 and h11

(c) h21 and h11 (d) None of these



2. A Signal x(t) has the Fourier transform

X( ) = { 1 for | | < }W . Its first zero-crossing in time domain occurs at:

O otherwise

(a) 1/pW (b) W

( c) p/ W (d) None of these










Computer Science



1. Magnetic tapes are suitable to applications:

(a) When only a few records are to be accessed

(b) When most of the records are to be accessed

(c) Only when all the records are to be processed

(d) None of the above



2. A system in which 2 or more cpu's are interconnnected and share a common

Main memory is called:

(a) Pipeline machine

(b) Multifunctional system

(c) Multiprocess

(d) None of these